Laser maintenance treatment and laser marking machine composition

Author: Correct Pack -Laser Marking Machine Manufacturer

The important part of the laser marking machine is the laser. The laser can be said to belong to the core part of the laser marking machine. The core part is well maintained. If you know how to deal with common problems, the frequency of failures and service life will increase. The laser has requirements on the environment. The working environment is water-cooled. We generally wait for the temperature of the chiller to reach 25 degrees before turning on the laser. We recommend that customers use it in a dust-free workshop. Dust may fall into the workshop with excessive dust. Lenses, reflectors, and beam expanders affect the weakening of the beam, and regular maintenance and cleaning are required to avoid affecting normal use. If the laser is not connected to power, do not rush to press the button on the laser. You should check whether the adapter is powered on, whether the device is grounded, whether the wire is damaged, etc. The indicator light next to it is not on, the laser does not emit light, and the marking software prompts that it is not connected or unavailable. After various investigations of the laser marking machine, the problem has not been solved. It is recommended to ask a professional to repair it.

If the temperature is too high, it is usually the alarm of the laser temperature is too high. The treatment method is to check whether the ambient temperature is too high or the internal temperature of the equipment is too high, consider whether the ventilation is good, and check whether the flow rate of the water cooler is too low or the cooling effect If necessary, turn off the computer, turn off the laser, turn off the key switch, and wait for professionals to arrive at the scene to investigate and solve the problem, so as to avoid damage to the laser or other components by wrong operation. It is recommended that the main power switch not be turned off, so that the UV laser can work in a dormant standby state , can maintain the temperature of the frequency doubling crystal, which is beneficial to the storage of the crystal and can prolong its service life at the same time. It is difficult to eliminate the weak laser beam. We first check whether the operating parameter frequency has changed. If it is too low, we must pay attention to it (the lower limit is 30KHZ), which may damage the crystal. If the problem is not resolved, check whether the power parameter has changed. If there is a change in the UV laser marking machine, the power parameters need to be increased. Generally, the pulse width and current are adjusted. If the above treatment is not resolved, it is recommended to check whether the lenses are covered by dust. Carry out regular inspection, cleaning and maintenance. If the above methods cannot solve the weak laser beam, professional personnel are required to deal with it. The composition is actually very simple, just like when we were new to computers, we didn’t know what accessories the computer was made of. With the home use of computers, we can now buy accessories and assemble them ourselves.

In the same way, with the wide use of it, we have a closer understanding of it. For its structure, the main accessory is an ultraviolet laser. This accessory is used to mark information on the product. It is not enough to have a laser. Focusing is required, vibrating mirrors, lenses, etc. are essential. They can focus the emitted light source to the point where the light is strong. They are pointy, so power is required to work normally. Heat is generated during work. The heat dissipation tool IC is fully automatic A laser marking machine is essential. You can use a fan or a water tank. These tools seem to be enough, but they are far from enough. We don’t like a machine that doesn’t listen to the control, so there must be a control card. We need flexibility and convenience. Editing things, the computer has a certain development history in editing patterns and texts. It is a good choice to connect the computer to the control card for editing. The main things can be roughly marked, and auxiliary equipment is also essential, such as red light. If No, we don’t know where it will be marked. At present, we don’t rely so much on red light. The light emitted by high power can also adjust the marking position. The workbench is also necessary. Different products generally use different workbenches. The working efficiency will be improved, and the production quality will be more optimistic. The main components and accessories are roughly as mentioned above, and the small accessories are not listed one by one, such as: switches, screws, fixed wires, etc. The specific accessories need to be based on customer needs. Different functions, auxiliary accessories may be increased. Zhuhai Correct Pack is a well-known laser equipment manufacturer in China. It has been focusing on the development and production of laser equipment for 12 years, providing customers with a complete set of laser equipment solutions, and creating cost-effective laser equipment. Main business: UV, co2, fiber laser marking machines, laser radium engraving machines And other cost-effective laser equipment, national service hotline: 400-0098-266https://www.xmslaser.com/.