Laser marking machine matters and common problems

Author: Correct Pack -Laser Marking Machine Manufacturer

Safe production, standardized operation, I believe that every factory has such display slogans, and the operation of laser marking machines also has strict specifications. Although the current machines are highly automated production and do not require manual operation processes, but many times It is still inseparable from labor. The following are some safety specifications for laser marking machines to operate nameplate marking machines:. 1. It is strictly forbidden to start the laser power supply and Q-switching power supply when there is no water or the water circulation is abnormal. 2. The Q power supply is not allowed to work without load (that is, the output terminal of the Q-modulated power supply is suspended).

3. If there is an abnormal phenomenon, first turn off the vibrating mirror switch and the key switch, and then check. 4. It is not allowed to start other components before the krypton lamp is ignited to prevent high voltage from entering and damaging the components. 5. Note that the output terminal (anode) of the laser power supply is suspended in the air to prevent ignition and breakdown with other electrical appliances.

6. Keep the internal circulating water clean, regularly clean the water laser marking chassis and replace it with deionized water or pure water. Laser marking machines are widely used in many fields, whether it is industrial, medical, scientific, manufacturing and other industries, there will be no shortage of laser marking machines. Although laser marking machines are highly automated processes in use, operators are still required In production, safety is the first priority, so we still need to be very careful in the process of using the laser marking machine. Only when we are familiar with the operation can we avoid failures. The laser marking machine gives some safe operation specifications: . 1. Be sure to do a safety check before operation. On the operation panel of the laser marking machine, there is an emergency stop button. This button is used in a very emergency situation. If you press such a red button, at this time Each axis will stop moving, and the laser high voltage will be turned off. If there is a very urgent situation during the operation of the ultraviolet laser marking machine, just press this button to stop the machine immediately.

2. To enter the safety door, the machine must be stopped first. A safety door will be installed on the front of the laser marking machine. This safety door is closed. Inside the machine tool is the space for various operating axes to operate. If the machine tool can work normally , the safety door will be closed. At this time, the operator must not enter the inside of the safety door for maintenance work. If you need to enter for inspection, you must first stop the machine. At this time, you can turn off the power of the machine tool or press the emergency button. Frequently asked questions about laser marking machines. Laser marking machine is a very common machine in the industry. It can print patterns, patterns, verification codes and other signs on the product. If the laser marking machine is used for a long time, some failures will occur. If it cannot be solved in time , it may have a great impact on the delivery time of the IC automatic laser marking machine. Most of the fault problems are not what we say can be solved. The maintenance of the laser marking machine is also troublesome, and there are also some minor problems that we can solve. It can be solved by yourself. The laser marking machine teaches you some common problems of laser marking machines and how to solve them:.

Fault 1: The laser intensity drops, and the marking is not clear enough. Solution:. Whether the laser resonator changes, fine-tune the lens of the resonator to make the output spot the best.

The acousto-optic crystal is offset or the output energy of the acousto-optic power supply is low. Adjust the position of the acousto-optic crystal or increase the operating current of the acousto-optic power supply. The laser entering the galvanometer is off-center: adjust the laser. If the current is adjusted to about 20A, the photosensitive intensity is still not enough: the krypton lamp is aging, replace it with a new lamp.

Fault 2: The krypton lamp cannot be triggered. Solution:. Check all power cables.

The high-voltage krypton lamp is aging, so replace the krypton lamp. Zhuhai Correct Pack is a well-known laser equipment manufacturer in China. It has been focusing on the development and production of laser equipment for 12 years, providing customers with a complete set of laser equipment solutions, and creating cost-effective laser equipment. Main business: UV, co2, fiber laser marking machines, laser radium engraving machines And other cost-effective laser equipment, national service hotline: 400-0098-266https://www.xmslaser.com/.