Advantages and safe operation guidelines of laser marking machines

Author: Correct Pack -Laser Marking Machine Manufacturer

Plastic and rubber, metal, silicon wafer and other materials, laser marking and traditional mechanical engraving, chemical corrosion. Compared with etching, screen printing, ink printing, etc., it has low cost, high flexibility, and can be controlled by a computer system. The firm and permanent mark produced by the laser acting on the surface of the workpiece is its outstanding feature. At present, laser marking machines has occupied a large share of the market. The reason why laser marking machines occupy such a large share is because it has the following eight advantages:.

1. The marking effect is permanent. For example, the marking will not fade due to environmental touch, acid and reducing gas, high temperature, low temperature, etc. 2.. Marking effect anti-counterfeiting:.

The mark engraved by laser marking machine technology is not easy to imitate and change. It is very strong to a certain extent. The anti-counterfeiting property.

3. Non-contact marking effect: Laser marking is a non-mechanical light knife. For processing, marks can be printed on any regular or irregular surface, and the workpiece will not generate internal stress after marking, ensuring the original precision of the workpiece, no corrosion on the working surface, and no tools. Abrasion, non-toxic, non-polluting.

4. The marking effect is applicable to many industries: using laser as a processing method can be used for various metal and non-metal materials. (aluminum, copper, iron, laser marking machine wood products, etc.) processing.

5. Marking effect High engraving precision: Since the pattern of the items engraved by the laser marking machine is beautiful and delicate, the minimum line width can reach 0.04mm. The mark is clear, durable, beautiful and feels good. need. For example, electronic components such as chips and triodes can enable the printing of two-dimensional barcodes that require more precision and higher definition. Compared with embossing or jet marking, the high-grade products have stronger market competitiveness.

First, you cannot enter the black screen of the operating system when you turn it on. If this problem occurs, we should first observe whether the work light is on normally. If it is not on, it may be that there is a problem with the 220V power supply, the insurance is burned, or the 12V switching power supply is burned. If If the working lights are normal but the display is black, there are three possible reasons: the display is damaged, whether the power cord from the main board of the industrial computer to the display is plugged in firmly, and the power supply of the industrial computer is not output, measure it, confirm that there is an input, then turn off the power and turn it on, the main thing is to listen to the main board Is there a beep? This sound means that the motherboard is not damaged. Check the 12V power supply. If the 12V power supply is plugged in well, it can be determined that the display is damaged. If the display shows“no signal”At this time, the problem is whether the display cable is plugged into the UV laser marking machine, the host will alarm (the sound is beeping), reinsert the memory module, if it still alarms, it can be judged that the motherboard is damaged, and it can be replaced directly. Second, the computer crash phenomenon of the laser marking machine may also be caused by a sudden power failure. Power failure generally causes different degrees of damage to the motherboard, hard disk and board of the industrial computer. If there is a problem with the light system, it will crash from time to time after entering. , this kind of phenomenon only needs to enter DOS to restore the system with ghost. If it still crashes from time to time, it is necessary to consider whether there is a problem with the hardware. The problem with the hard disk accounts for most of the problems, and it may also be caused by the motherboard. Be sure to bring some of the main components in the IPC. 1. Comply with the general cutting machine safety operating procedures, and start the fiber laser in strict accordance with the fiber laser start-up procedure.

2. The operator must be trained to be familiar with the structure and performance of the equipment, and to master the relevant knowledge of the operating system. 3. Wear labor protective equipment according to the regulations, and must wear protective glasses that meet the regulations near the fiber laser beam. 4. Before finding out whether a material can be irradiated or heated by fiber laser, do not process it to avoid potential hazards.

IC automatic laser marking machine 5. When the equipment is in operation, the operator is not allowed to leave the post without authorization or entrust someone to be in charge. If it is really necessary to leave, the operator should stop the machine or cut off the power switch. 6. Keep fire extinguishers within easy reach, turn off fiber lasers or shutters when not processing, and do not place paper, cloth or other flammable materials near unprotected fiber laser beams. 7. When abnormalities are found during processing, stop the machine immediately and troubleshoot in time.

8. Keep the fiber laser, the bed and the surrounding area clean, orderly, and free of oil, and the workpieces, plates, and waste materials are piled up according to regulations. 9. When using gas cylinders, avoid crushing the welding wires to avoid electric leakage accidents. The use and transportation of gas cylinders should comply with gas cylinder monitoring regulations. Stand on the side of the bottle mouth. 10. During maintenance, high-voltage safety regulations must be followed. Every 40 hours of operation or weekly maintenance, and every 1000 hours of operation or six-month maintenance must be carried out in accordance with the regulations and procedures.

11. After turning on the machine, start the machine tool manually at low speed in X and Y directions, and check to see if there is any abnormality. 12. After inputting the new workpiece program, it should be trial run first and check its running condition. 13. When working, pay attention to observe the operation of the machine tool to avoid accidents caused by the cutting machine going out of the effective stroke range or two collisions.

Zhuhai Correct Pack is a well-known laser equipment manufacturer in China. It has been focusing on the development and production of laser equipment for 12 years, providing customers with a complete set of laser equipment solutions, and creating cost-effective laser equipment. Main business: UV, co2, fiber laser marking machines, laser radium engraving machines And other cost-effective laser equipment, national service hotline: 400-0098-266https://www.xmslaser.com/.